|
TechSpec Caution
|
It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after installation. |
|
TechSpec Overall Height (in)
|
2.5 |
|
TechSpec Overall Length (in)
|
28.6 |
|
TechSpec Overall Width (in)
|
12.3 |
|
TechSpec Inlet
|
N/A |
|
TechSpec Outlet
|
N/A |
|
TechSpec Includes
|
Application Specific Mounting Bracket / Air Diversion Shield--Bar and Plate Oil Cooler--2ft 3in Stainless Steel Braided Hose w/ -10AN Fittings--4ft 8in Stainless Steel Braided Hose w/ -10AN Fittings--M22 Thermostatic Sandwich Plate--Application - Specific, M22 x 1.5 extended length center bolt--M20 x -10AN Straight Fittings--1/8-in NPT Plugs--Large O-ring--Lower Radiator Hose w/ worm gear clamps--Mounting Hardware Set--Mishimoto Lifetime Warranty |
|
TechSpec Applications
|
2018-2023 Ford Mustang GT (Right Hand Drive vehicles only) |
|
TechSpec Fluid Capacity (qts)
|
1 |
|
TechSpec Note
|
Requires the removal of the stock coolant based oil cooler.----Installation requires the removal of the active grill shutters. Removal without tuning can cause a check engine light.----Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb |
|
SellingPoint01
|
Direct fit for the 2018-2023 Ford Mustang GT RHD |
|
SellingPoint02
|
Innovative bar-and-plate oil cooler mounts in the upper grille, allowing more room for supercharger heat exchangers |
|
SellingPoint03
|
Mounting bracket also serves as an air diversion panel, directing the maximum amount of ambient air through the oil cooler |
|
SellingPoint10
|
Mishimoto Lifetime Warranty |
|
SellingPoint11
|
N/A |
|
SellingPoint12
|
N/A |
|
SellingPoint13
|
N/A |
|
SellingPoint14
|
N/A |
|
Install Difficulty
|
4 |
|
SellingPoint15
|
N/A |
|
OptionLabel
|
Black, Thermostatic |
|
Prop 65 Y/N
|
Y |
|
Prop 65 - Short Label
|
WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov |
|
TechSpec Rows
|
12 |
|
TechSpec Core Construction
|
N/A |
|
TechSpec Core Length (in)
|
18.5 |
|
TechSpec Core Height (in)
|
N/A |
|
TechSpec Core Thickness (in)
|
N/A |
|
TechSpec Engine Codes
|
5.0 Coyote III |
|
TechSpec Chassis Codes
|
S-550 |
|
TechSpec Installation Notes
|
N/A |
|
SellingPoint04
|
Pre-made stainless steel braided oil lines with durable -AN fittings |
|
SellingPoint05
|
Comes with replacement lower radiator hose to bypass the stock fluid-based oil cooler |
|
SellingPoint06
|
Removes the stock fluid-based oil cooler for less stress on the engine's cooling system |
|
SellingPoint07
|
Billet aluminum thermostatic oil sandwich plate |
|
SellingPoint08
|
Increases oil capacity by 1qt |
|
SellingPoint09
|
Fits with most aftermarket supercharger kits |
|
Base Height
|
2.5 |
|
Color
|
Black |
|
Core Color
|
Black |
|
Core Height
|
0 |
|
Core Row Quantity
|
0 |
|
Core Thickness
|
0 |
|
Core Type
|
Bar-and-Plate |
|
Core Width
|
18.5 |
|
Finish
|
Anodized |
|
Fluid Capacity
|
1 |
|
Grade Type
|
Performance |
|
Inlet Fitting Gender
|
Male |
|
Inlet Fitting Type
|
AN Flare |
|
Inlet Outside Diameter
|
0 |
|
Outlet Fitting Gender
|
Male |
|
Outlet Fitting Type
|
AN Flare |
|
Outlet Outside Diameter
|
0 |
|
Width
|
12.3 |
